PROCESSOR & PACKAGE STYLE

Intel® Pentium® 4 Processor - 2.8GHz, 2.4GHz and 2.0GHz embedded CPU speeds
Processor Package = FC-PGA2/mPGA478

CACHE MEMORY (L2)

Intel® Pentium® 4 Processor (Northwood) - 512KB

CHIPSET

The Intel® 845E Chipset with the Intel® ICH4 I/O Controller Hub

SYSTEM BUS & MEMORY

System Bus = 533/400MHz
Memory Interface Structure = Single-channel interface with two DDR DIMM sockets
Class = DDR-266
Max. = 2GB
Min. = 64MB
DIMM Type = PC-2100, PC-1600, 72-bit with ECC, unbuffered
DIMM Construction = 184-pin, gold card-edge fingers

EDGE CARD INTERFACES

PCI/ISA Parallel Bus Support:

VIDEO INTERFACE

Video Controller: Intel® 69030
Memory: 4MB
Resolution: Up to 1280 x 1024 (SXGA)

BATTERY

Type: Lithium
Purpose: CMOS data retention

I/O INTERFACES

USB: 2, USB 2.0 interfaces - on-board header
Floppy: 1, on-board connector
PS/2 Keyboard & Mouse: I/O bracket connector
Serial: 2, on-board port headers
Parallel: 1, on-board connector (EPP and ECP modes are IEEE 1284 compliant)
Ultra ATA/100: 2, primary & secondary IDE connectors
Speaker: 1, on-board header
Ultra160 SCSI: 1, on-board connector

BIOS (FLASH)

The T4I uses AMIBIOS8®. The flash BIOS resides in the Firmware Hub (FWH). AMIBIOS8 contains features such as:

• Support for flash devices for BIOS upgrading via floppy interface
• Integrated support for USB mass storage devices such as CD-ROM, CD-RW, DVD-RW, etc.
• Boot from network, USB mass storage devices, IDE, SCSI or ATAPI
• Serial port console redirection to support headless operation
• SATA/ATA/ATAPI support includes 48-bit LBA addressing to support SATA/ATA/IDE hard drive capacities over 137GB

ETHERNET INTERFACES

I/O Bracket = 2
LAN1 = 10/100Base-T via the Intel® ICH4 & Intel® 82562ET PHY
LAN2 = 10/100/1000Base-T via the on-board PCI bus & Intel® 82540 Ethernet Controller
I/O Bracket Connectors = RJ-45

STANDARDS

- IEEE P996, Personal Computer Bus Standard
- PCI Local Bus Specification 2.1
- PICMG 1.0 Specification
- Ultra160 SCSI, SPI-3 Standard

WATCHDOG TIMER

This programmable watchdog timer provides a system reset with a total range of 30ms to 60 seconds.
The programmable increments of the watchdog are 30ms, 10s and 60s.

MECHANICAL

Standard Cooling Solution = Fan + heatsink
Std. CS Height Range = 1.65" (41.91mm) to 1.80" (45.79mm)

T4I Dimensions = 13.33" (33.858cm) L x 4.80" (12.19cm) H

AGENCY APPROVALS & COMPLIANCE

Designed for UL60950, CAN/CSA C22.2 No. 60950-00, EN55022:1998Class B, EN61000-4-2:1995, EN61000-4-3:1997, EN61000-4-4:1995, EN61000-4-5:1995, EN61000-4-6:1996, EN61000-4-11:1994

MEAN TIME BETWEEN FAILURES (MTBF)

118,992 POH (Power-On Hours) at 40 ^oC., per Bellcore.

POWER REQUIREMENTS - 100% stressed

Typical Values

-12V @ < 100mA*

* From Backplane via PICMG® Connector.
# From ATX12V power supply or equivalent via P4 connector.

The Intel® Pentium® 4 power requirements created the need for an additional on-board 4-pin power connector (P4). This connector requires +12V from an external power supply that conforms to the ATX12V power specification.

This external power supply should have a minimum wattage rating of at least 250W. The T4I also requires that 3.3V be applied to the backplane from the power supply.

The system power supply must conform to the power sequencing specifications of ATX compliant power supplies. Voltage levels must be regulated within a range of +/- 5%.

POWER REQUIREMENTS - Idle

Not applicable

TEMPERATURE & ENVIRONMENTALS

OTHER ENVIRONMENTAL REQUIREMENTS

MEMORY SLOT POPULATION

Memory modules can be installed in one or both DIMM sockets. If only one DIMM module is used, it should be populated in the top DIMM socket (Bank 2 - Bk2). If two modules of different speeds are used, the 845E chipset sets the memory interface speed to the speed of the slower DIMM module. Registered DIMMs are not supported. All memory modules must have gold contacts.

IOBxx EXPANSION BOARDS (OPTIONAL)

Not Applicable