T4R |PICMG 1.0| Celeron Single Board Computer (SBC)
Description
Trenton's T4R is specifically designed to simplify upgrading older Intel® Pentium®, Intel Pentium® II or Intel® Pentium® III SBCs with a high performance Intel® Pentium® 4 or a Mobile Intel® Pentium® 4 Processor-M single board computer. The T4R generates its own +3.3V on board and provides the ability to route the +5V over to the +12V lines of the T4R's processor. These power control features enable the T4R for use as a simple drop-in SBC upgrade in PICMG® 1.0 embedded computing systems. Contact the single board computing experts at Trenton to discuss your unique system upgrade requirements.
Model number and model name definitions:
6401 T4R = Celeron processor, standard-memory configuration
|
PROCESSOR & PACKAGE STYLE
Intel® Pentium® 4 Processor - 2.8GHz and 2.4GHz embedded CPU speeds
Mobile Intel® Pentium® 4 Processor-M - 1.7GHz and 2.2GHz
Processor Package (P4) = FC-PGA2/mPGA478
Processor Package (P4M) = FC-PGA/mPGA478
|
CACHE MEMORY (L2)
Intel® Pentium® 4 Processor & Mobile Intel® Pentium® 4 Processor-M (Northwood) - 512KB
|
CHIPSET
The Intel® 845E Chipset with the Intel® ICH4 I/O Controller Hub
|
SYSTEM BUS & MEMORY
System Bus = 533/400MHz
Memory Interface Structure = Single-channel interface with two DDR DIMM sockets
Class = DDR-266
Max. = 2GB
Min. = 64MB
DIMM Type = PC-2100, PC-1600, 72-bit with ECC, unbuffered
DIMM Construction = 184-pin, gold card-edge fingers
|
|
EDGE CARD INTERFACES
PCI/ISA Parallel Bus Support:
|
|
|
ISA |
16-bit/8MHz |
|
|
|
|
PCI |
32-bit/33MHz |
|
|
|
|
|
|
|
VIDEO INTERFACE
Video Controller: ATI® RAGE® MOBILITY® M1
Memory: 8MB
Resolution: Up to 1280 x 1024 (SXGA)
|
BATTERY
Type: Lithium
Purpose: CMOS data retention
|
I/O INTERFACES
USB: 2, USB 2.0 interfaces - on-board header
Floppy: 1, on-board connector
PS/2 Keyboard & Mouse: I/O bracket connector
Serial: 2, on-board port headers
Parallel: 1, on-board connector (EPP and ECP modes are IEEE 1284 compliant)
Ultra ATA/100: 2, primary & secondary IDE connectors
Speaker: 1, on-board header
Ultra160 SCSI: 1, on-board connector (optional)
|
|
BIOS (FLASH)
The T4R uses AMIBIOS8®. The flash BIOS resides in the Firmware Hub (FWH). AMIBIOS8 contains features such as:
- Support for flash devices for BIOS upgrading via floppy interface
- Integrated support for USB mass storage devices such as CD-ROM, CD-RW, DVD-RW, etc.
- Boot from network, USB mass storage devices, IDE, SCSI or ATAPI
- Serial port console redirection to support headless operation
- SATA/ATA/ATAPI support includes 48-bit LBA addressing to support SATA/ATA/IDE hard drive capacities over 137GB
|
ETHERNET INTERFACES
I/O Bracket = 2
LAN1 = 10/100Base-T via the Intel® ICH4 & Intel® 82562ET PHY
LAN2 = 10/100/1000Base-T via the on-board PCI bus & Intel® 82541 Ethernet Controller
I/O Bracket Connectors = RJ-45
|
STANDARDS
- IEEE P996, Personal Computer Bus Standard
- PCI Local Bus Specification 2.1
- PICMG® 1.0 Specification
- Ultra160 SCSI, SPI-3 Standard
|
WATCHDOG TIMER
WATCHDOG TIMER:
Component: I/O Controller Hub,two-stage watchdog timer (WDT)
Functions: Two programmable operating modes - free-running and one-shot
Stage one: Generates IRQ, SMI or SCI
Stage two: Generates WDT reset with a total range of 30ms to 60s with programmable increments of 30ms, 10s and 60s.
SYSTEM HARDWARE MONITOR:
Component: Winbond W83783S
Functions:
Voltage Monitoring: +2.5V, +3.3V, +/-12V, +5V and VCORE
Fan Speed
Temperature
Monitor limits are user programmable
|
|
MECHANICAL
Standard Cooling Solution = Fan + heatsink
Std. CS Height Range = 2.18" (55.37mm) to 2.33" (59.25mm)
T4R Dimensions = 13.33" (33.858cm) L x 4.80" (12.19cm) H
|
AGENCY APPROVALS & COMPLIANCE
Designed for UL60950, CAN/CSA C22.2 No. 60950-00, EN55022:1998Class B, EN61000-4-2:1995, EN61000-4-3:1997, EN61000-4-4:1995, EN61000-4-5:1995, EN61000-4-6:1996, EN61000-4-11:1994
|
MEAN TIME BETWEEN FAILURES (MTBF)
144,036 POH (Power-On Hours) at 40 oC., per Bellcore
|
|
POWER REQUIREMENTS - 100% stressed
The following are typical values:
|
+ 5V Operation: |
|
Processor Speed |
+5V |
+12V |
+3.3V |
|
Intel® Pentium® 4: |
|
2.8GHz |
12.2A |
0.5A |
None |
|
2.4GHz |
11.9A |
0.5A |
None |
|
Mobile Intel® Pentium® 4 Processor-M: |
|
2.2GHz |
5.51A |
0.34A |
None |
|
1.7GHz |
4.52A |
0.37A |
None |
|
|
|
|
|
|
+5V and +12V Operation: |
|
Intel® Pentium® 4: |
|
2.8GHz |
2.5A |
4.9A |
None |
|
2.4GHz |
2.5A |
4.5A |
None |
|
Mobile Intel® Pentium® 4 Processor-M: |
|
2.2GHz |
1.67A |
3.49A |
None |
|
1.7GHz |
1.67A |
3.13A |
None |
-12V @ <100mA
Tolerance for all voltages is +/-5% |
POWER REQUIREMENTS - Idle
Not Applicable
|
|
TEMPERATURE & ENVIRONMENTALS
|
Standard Operating Temperature: |
0 oC to 45 oC. |
|
Storage Temperature |
-20 oC to 70 oC. |
|
OTHER ENVIRONMENTAL REQUIREMENTS
|
Airflow Requirement: |
300LFM continuous airflow |
|
Humidity |
5% to 90% non-condensing |
|
|
MEMORY SLOT POPULATION
Memory modules can be installed in one or both DIMM sockets. If only one DIMM module is used, it should be populated in the top DIMM socket (Bank 2 - Bk2). If two modules of different speeds are used, the 845E chipset sets the memory interface speed to the speed of the slower DIMM module. Registered DIMMs are not supported. All memory modules must have gold contacts.
|
|
IOBxx EXPANSION BOARDS (OPTIONAL)
Not Applicable
|
|
